EGX200/EGX400 Firmware
Use the links below to transfer the latest EGX200/400 firmware to your Computer. Note: Communication to serial devices through the EGX during firmware updates is not available. Communications should be restored automatically in most Powerlogic Systems.
EGX200 -- The version 6.1 firmware update includes better broadcast/multicast storm resiliency, auto negotiation improvements, serial communications support for Odd parity, and the ability to communicate with ModbusTCP/IP protocol over nonstandard MTU sized Ethernet networks.
To properly update your EGX200:
1. Transfer the version 6.1 firmware file (egx06100.bin) to your Computer.
2. Use FTP to copy the "egx06100.bin" file from your Computer to the EGX (once the file transfer is complete, the EGX will automatically reboot). Refer to the EGX 200/400 Users Guide if you need more information.
3. Allow the EGX to reboot after the file transfer and browse the EGX to confirm v6.1 is displayed.
EGX400 -- Upgrading the EGX400 to version 6.1 provides all the features of the EGX200 mentioned above plus data logging enhancements, increased support for the number of loadable device types (PLT files) from 32 to 64, SMTP client enhancements, and additional device type support for the ION7300.
To properly update your EGX400, the following steps must be followed in order:
1. Browse the EGX to record the device list entries and which devices are being logged.
2. (Optional) Use FTP to retrieve all currently logged data (".log" files) from the EGX. (Note: all logged data will be lost in step 6)
3. Transfer the version 6.1 firmware file (egx06100.bin) to your Computer.
4. Use FTP to copy the "egx06100.bin" file from your Computer to the EGX (once the file transfer is complete, the EGX will automatically reboot). Refer to the EGX 200/400 Users Guide if you need more information.
5. Allow the EGX to reboot after the file transfer and browse the EGX to confirm v6.1 is displayed.
6. Use FTP to delete all ".plt" files from the EGX (this will cause all logged data to also be deleted).
7. Transfer the version 6.1 ZIP file (egx06100.zip) to your Computer.
8. Extract the files from the "egx06100.zip" file to a known location on your Computer.
9. Use FTP to copy all extracted files to the EGX, overwriting all existing files.
10. Browse the EGX and re-setup the device list and logging using what was recorded in step 1.
SEPAM - SFT2841 V11.1 Setting Software
The SFT2841 V11.1 software is the setting and operating tool for Sepam Series 20, Series 40 and Series 80 relays. It may be used in one of three operating modes.
- Offline mode - prior to commissioning and without connection to the Sepam relay to prepare protection and parameter settings
- Online mode - during commissioning, on a PC connected point-to-point to the Sepam front panel using the CCA783 serial cable: to load, upload and modify Sepam relay protection and parameter settings and to obtain all measurements and useful information during commissioning
- Network mode - during operation, on a PC connected to a set of Sepam relays via an E-LAN multipoint communication network in order to manage the protection system, to monitor the status of the electrical network and to run diagnostics on any incidents affecting the electrical network.
Minimum system requirements for SFT2841 are:
- Microsoft Windows 2000 / XP/ Vista
- Pentium 133 MHz (or more)
- 64 Mb RAM
- 200 MB of available disk drive
- CD-ROM drive
- 800x600, 65535 colors
INSTALLATION OF THE COMPLETE VERSION OF SFT2841
To install the complete version of SFT2841, the software serial number is required. Only SFT2841 software delivered with the connection cable (CCA783) is needed for connected mode operations. The software serial number can be found on a sticker on the CD-ROM box. It is possible to re-use a serial number for newer versions of SFT2841. Or you may use the serial number below:
Serial Number: 0647740-08
INSTALLATION OF THE DEMONSTRATION VERSION OF SFT2841
The installation of SFT2841 in demonstration version is always possible. (no serial number required). The SFT2841 demonstration software offers all the functions of the complete version, with the exception of the functions available in connected mode and the file saving function. Instructions: Download SFT2841 download and installation instructions.doc. Follow the instructions to download and install SFT2841.
- SEPAM SFT2841 V11.1 Setup - The SFT2841 V11.1 software is the setting and operating tool for Sepam Series 20, Series 40 and Series 80 relays
